HP LaserJet 1320tn
I replaced the toner in this HP LaserJet 1320tn and the "change toner light" on top of the machine remains on. Also, it still prints while calling for toner. Why would it still be asking for toner...
View ArticleStaples, Inc. Earnings: Can Office Retail Survive?
Even as it deals with brick-and-mortar rival Office Depot and its efforts to restructure itself to become more efficient, Staples has had to work hard to bolster its online presence to fight poaching...
View ArticleClik here to view.
BizHub 601
Installed new drum and 250K pm kit. I didn't do the developer because I had just done that a week ago. Quality was good before I did the work. After work the copies are washed out. I went back over my...
View ArticleMX-5001N Lost Web page password
Somehow the web page password has been changed. And themachine has a security data kit inside (MX-FR11U). So, I can't do a 24-30 or24-31. Read there might be some dip switches I could turn on and force...
View ArticleXEROX 7655 configuration mismatch
hello i have this problem alwyas i start the machine and meanwile it says comunication error can anyone get to me wcpp diagnostic software
View ArticleIR 550 tech in Michigan
Picked up an IR 550. Has an error jam in document feeder. Couldn't find anything. No experience with Cannon. Looking for an independent tech in the Brighton / Jackson / Ann Arbor area.
View ArticleClik here to view.
HP Designjet 70, part # please.
HP Designjet 70. What is the part # of this broken off flap/holder/guide thingamajig holding the ink cartridges in place please? Thanks Hans Attached Images DJ70.jpg (423.7 KB)
View ArticleC35 0warmup problem
hi all, my clients C 350 dose not complete the warmup sequence it just show ready to copy.when the print is release the data shows in the job list but shows paper jam error but no paper inside. the...
View ArticleMBM/Ideal/Destroyit 4002 cross cut shredder reverse but no forward
Removed all paper debris from shredder and changed 2 gears in gearbox thought to have had wear but in retrospect were probably okay. Shredder goes in reverse but when press forward with paper in...
View ArticleC350 warmup problem
hi all, my clients C 350 dose not complete the warmup sequence it just show ready to copy.when the print is release the data shows in the job list but shows paper jam error but no paper inside. the...
View ArticleFaint cyan and magenta on C7000P
Hi all, Yellow and black prints very well, but magenta and cyan are both very faint causing the machine to flag all sorts of codes (especially 4603 and 2803) after switching it on during auto...
View ArticleMiscellaneous pro 1106ex
I have problem with pro 1106ex i have not toner and developer for this machine, my qustion can user toner mp 6001 and developer type 24 with quantity 1250gm for developer.
View ArticleJamming Ricoh MP-301sp Jamming in 2-sided on RDF
Hi everyone. I have 2 RICOH MP-301sp with the same problem, jams on the RDF "ONLY IN 2-SIDED MODED AND ONLY WHEN I PUT MORE THAN I ORIGINAL ON IT". I belive its firmware related but here in Mexico the...
View ArticleMPC2500 Paper Crumple in A3 Size
Hi ! Im facing some problem when i using A3 size print in Tray 2,3,4 in MPC2500. it come out Paper Crumple. But using A4 paper Size in Tray 1,2,3,4. No Problem. When i use A3 paper size in Bypass, it...
View ArticleKyocera Device Cloning ETC.
Do current Kyocera MFPs have any device cloning like Sharp and Ricoh do. Or is there a software tool I can use for the configuration of large numbers of devices like HPs WJA? I can't think of anything...
View ArticleClik here to view.
Zombie Avatar set added
If you've ever dreamed of a cool new Zombatar, today is your lucky day. We have added some new avatars, click the following link to check them out: Zombie Avatar Set
View ArticleZombie Avatar set added
If you've ever dreamed of a cool new Zombatar, today is your lucky day. We have added some new avatars, click the following link to check them out: Zombie Avatar Set. Click here to discuss this post
View ArticleCQ Pro C5100 - 1st side magnification issue
Hi, Have a Pro C5100, adjusting the second side magnification is easy BUT can you adjust the first side magnification?? The customer is printing a 420mm wide rectangle on an SRA3 page but its coming...
View ArticleDead Machine Xerox ColorQube 9301 will not boot into UI, Machine Locked in UI
I´ve get an Colorqube 9301, after Switch on, I will see the Xerox Screen with the message - Booting please wait, aber hours nothing more and the UI is not Accessable ? the UI Looks like it is locked,...
View Articleerror code sc 77-01 BH1050e
Hi guys, does anyone knows sc77-01 for BH1050e. the machine just pointing finisher failure. Can u pls help me guys. Thanks
View Article